ULOG DAY 8: "(LETTER CUTTING) BE AN ULOGGER"
Dear Uloggers,
I was sleepy last night but my eyes were awakened quickly when I saw the post of Sir @surpassinggoogle about #ulog. To be a responsible ulogger, we should always put the number of the day of our #ulog title and make the #ulog the main tag. I like everything in #ulog because it is our online diary where anybody can give their advice if our write-ups need advice. Mostly, I like it because our number one fan is Sir @surpassinggoogle. So, join #ulog now. Below are the rules how to deserve to be an ulogger.
How to Be an Ulogger
- Use #ulog only when you consider your post a ULOG.
- Ulog once a day.
- Add #ulog to the tittle and add number to it.
e.g: #ulog day #1.- Use your Ulogger footers/headers.
- Use Ulog/Ulogs as your main tag then continue four other tags you normally would.
- Ulog can contain pictures but these shouldn't be from the Internet instead should be fresh pictures involving you or the events and locations within your day.
- No plagiarism.
Source: Sir @surpassinggoogle
In support to #ulog, today, I letter cut "Be an Ulogger" as my campaign. How did I cut each letter? Below are the steps.
How to Cut "Be an Ulogger"
B - Steps:
- Match the upper points to the lower points in each to the bottom and fold.
- Trim V-cut of the upper point and reversed C-cut of the lower-right point/side.
- Fold the paper vertically and cut the area in the middle by leaving the margin according to your preferred size of the letter. Begin trimming from the upper-right side down to the lower side that reaches the middle line.
- Leave a little margin when reaching the middle line downward.
- Unfold the paper.
E-Steps:
- Match the upper points to the lower points and crease well.
- Trim the area below the upper side or provide margin depending on your letter-size choice. Begin trimming from the right side. Do not trim until to the left side.
- Trim another line below the trimmed line from the top from the left side. Do not trim until to the left side.
- Cut the middle area.
A-Steps:
- Match the left vertices to the right.
- From the upper point, cut a slanting trimming to the lower-side point.
- Leave a margin from the bottom and trim a shortened horizontal line above the margin. Do not cut until the end or to the side.
- Continue cutting from the horizontal line to the top and horizontal line again going to the right side. Cut through the sides.
- From the bottom, cut another slanting cut shortened line that leaves the margin from the lower-left side. Continue cutting by forming a horizontal line until to the left side. Trim finely and unfold.
N-Steps:
- Match the upper sides to the lower sides and crease to create a middle line.
- Leave a margin from the lower-left side and make a vertical cut from the bottom to the middle line.
- Leave a margin from the lower-right side and do the slanting cut to the middle line reaching the vertical cut.
- Reverse the paper and repeat the Step 3.
U-Steps:
- Match the left vertices to the right and fold.
- Cut a reversed letter C at the lower-side point. To be simple, form reversed letter C-cut.
- Cut the middle area by leaving a margin of the right side. Cut a reversed L thoroughly to the left side. Unfold.
L-Steps:
- Cut letter L leaving a margin from the left side to your letter preference size.
O- Steps:
- Match the upper side to the lower side and crease.
- Match the left-side to the right-side and crease.
- Trim letter C-cut to the upper-right point.
- In the middle, cut letter L.
- Unfold.
G-Steps:
- Match the lower and upper sides to form a middle line. Crease.
- Fold again by matching the left points to the right.
- Trim letter C on the upper-right side.
- Unfold.
- From the right-middle side, trim the paper following the middle line going to the top and then moving to the left angle below the middle line.
- Continue trimming from the middle line downward, then to the right side, to the upper-right side and again to the left.
- Cut the middle line moving downward. Cut the excess.
R-Steps:
- Match the upper side to the lower side and crease.
- Cut C-cut at the right top point.
- Trim V-cut at the right-lower point. Unfold.
- Leave a margin from the left-lower side and make a vertical cut to the top that doesn't reach the middle line.
- Trim a horizontal line to the right side that doesn't reach the side, then trim letter C moving to the bottom.
- Fold the first part of the vertical line paper to make a middle line on its part.
- Trim a C cut.
- Unfold.
This is my new #ulog footer/banner. The original #ulog footer/banner is amazing but I can't download over the phone and my laptop is freezing, so I got this letter cutting idea. As we see, it doesn't look good for me so I'm gonna try making again soon because the compilations of Sir @surpassinggoogle deserve a lot of efforts. He doesn't want to pressure us but we should do our best to protect his reputation and dignity.
What are you waiting for, #ulog now and let your emotions be heard around the world. Steemit is your home where you are comfortable to share your inner being and #ulog is a Steemit community that truly rewards our daily sentiments fairly. It's a gift for us minnows that our pure writings are not ignored so we should accept this gift, follow the rules and make it a routine.
Disclaimer: The content and illustrations are original unless sourced/credited/qouted.
#4 alin bang footer/header dami na kasi pag dinagdag ko yun ginagamit ng iba eh
@pinay, bisitaha ang profii sir SG
Post I mean. Hehehe
Natatabunan kasi ng resteem eh 😅
STOP